Launch X-431 Pad 7 Solved VW Passat 2019 B1168F2 DTC

This is how to solve Volkswagen Passat 2019 power steering DTC B1168F2 with Launch X-431 Pad 7 in steps. Efficiency is greatly improved by using the guided function. Read this post to learn how to do it.


Connect X-431 Pad 7 to OBD,

Local Diagnose >> VW >> Enter 44 Power Steering Trouble Code:

B1168F2 Steering Angle Sensor - No Initialization

OK >> Read DTC

launch-x-431-pad-7-solved-vw-passat-2019-dtc-1

launch-x-431-pad-7-solved-vw-passat-2019-dtc-2

Guided Functions >> Select Vehicle Model, Year & Engine Type >> Start >> Power Steering >> Guided Functions >> 0044 - Basic Setting Steering Angle Sender - G85

launch-x-431-pad-7-solved-vw-passat-2019-dtc-3

launch-x-431-pad-7-solved-vw-passat-2019-dtc-4

launch-x-431-pad-7-solved-vw-passat-2019-dtc-5

launch-x-431-pad-7-solved-vw-passat-2019-dtc-6

Follow the instruction on X-431 Pad VII, and press "Continue":

- Start engine.

- Turn to steer until the first mechanical end stop is contacted. The sequence left/right is insignificant.

- Turn to steer until the other mechanical end stop is contacted.

- Turn the steering back to its center position.

- Check yellow warm. Lamp in the instrument cluster.

Warn, Lamp in instrument cluster must extinguish.

Did the warning lamp extinguish? Yes

- Switch the engine off.

The initialization of the steering angle sensor - G85 was successfully performed.

Here, the program will be ended.

launch-x-431-pad-7-solved-vw-passat-2019-dtc-7

launch-x-431-pad-7-solved-vw-passat-2019-dtc-8

Go back to "Clear DTCs".

The trouble code B1168F2 was successfully solved.


More info about Launch- x431 diagnostic tools to be updated...

launch-x-431-pad-7-solved-vw-passat-2019-dtc-9

launch-x-431-pad-7-solved-vw-passat-2019-dtc-10

www.obd2shop.co.uk

Comments

Post a Comment

Popular posts from this blog

Launch X431 CRP919X BT Register and Update

Image
This post will show you how to register and update the Launch X431 CRP919X BT Diagnostic Tool . Follow the steps below to sign in and update: Tap Login on the upper right corner of the home screen, and the following login window will pop up. If you are a new user, follow A to proceed. If you have registered to be a member, go to B to log in to the system directly. In case you forgot your password, refer to C to reset a new password. A. If you are a new user, tap [New Registration] to enter the sign-up page. Fill in the information in each field (Items with * must be filled). After inputting, tap [Register], the following screen will appear: Input the 12-digit Product Serial Number and 8-digit Activation Code (which can be obtained from the password envelope), and then tap [Activate]. Tap [OK] to navigate to the update center to update all available software. After the registration is successfully complete, the wireless communication between the tablet and the VCI device is automaticall...
Read more

What is Launch X431 Key Programmer and how to use it?

Image
Launch x431 key programmer specializes in reading and writing key information, generating various key chips, etc. Currently, it can only be used with X431 IMMO Elite , X431 IMMO Plus , X431 PAD V (PAD 5), and X431 PAD VII (PAD 7) . How to use the x431 key programmer? 1. Use with Super Chips On the tablet (this item uses PAD V as an example), open the X431 PAD V APP, select "Other Modules" >> "Toolbox" >> "Key Programming" Enter the "Set Super Chip Type" menu to generate. Select the corresponding key chip type and insert the super chip into the anti-theft induction coil. Once successfully generated, it can be used. 2. Use with Super Remotes Take LS Nissan super remote as an example: The initial operation is the same as the super chip, enter the "Key Programming" menu and select "Vehicle Remote", then select the corresponding smart key model to generate. Place the electronic remote key in the key programmer to gener...
Read more

Launch X431 IMMO Plus Program Ford Engine Module Replacement

Image
This is a tutorial on how to use Launch X431 IMMO Plus to program Ford engine module replacement. Besides, the X431 IMMO Plus programming tool also supports anti-theft module replacement of BMW, Mercedes-Benz, VW/Audi, Honda, Nissan, Hyundai, etc. Read this article carefully to learn how to do it. Procedure Connect X431 IMMO Plus to car OBD. IMMO >> Ford >> Anti-theft system detection >> Automatically search Set the ignition switch to ON(Position II). Please confirm VIN and VIN code, and press "Yes". Immobilizer system function(expert edition) >> PATS(Passive Anti-Theft System) Functions Set the ignition switch to on. Module initialization >> PCM(powertrain control module) Set the ignition switch to OFF(Position 0). Operation in progress. Please wait until 100%... Set the ignition switch to ON. Retrieving data for coded access procedure... Please confirm VIN and VIN code, and press "Yes ". Set the ignition switch to OFF(Position 0). P...
Read more