Launch X-431 Pad7 Register New Nissan X-Trail ECM VIN

This is a guide to using Launch X-431 Pad VII to perform new ECM(Engine Control Module) VIN registration for a 2017 Nissan X-Trail T32. It's very helpful for ECM replacement in vehicle repair.


Procedure

Nissan Latest version >> Full system diagnosis >> The vehicle with 16PIN >> System selection >> Engine >> ECM(Engine Control Module)

X-431 Pad7 is scanning ECU... please wait

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-1

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-2

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-3

Special function >> VIN registration

Confirm the ignition switch is on and the engine stopped.

Hold these conditions during this procedure.

Touch start.


As we can see, the VIN/Chassis value is blank now.

VIN Read >> Input

Input the VIN of the vehicle. Refer to S/M for the location of the identification plate.

Write >> Input

Input VIN once again.

Press "Start".


Command succeeded.

Turn the ignition switch off for 10s, then the ignition switches on to confirm no DTC.

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-4

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-5

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-6

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-7

Exit to enter into "VIN registration" again.

The VIN/Chassis value was displayed, which means the VIN number has already been registered successfully.

Done.

launch-x-431-pad7-register-new-nissan-x-trail-ecm-vin-8

www.obd2shop.co.uk

Comments

Post a Comment

Popular posts from this blog

Launch X431 CRP919X BT Register and Update

Image
This post will show you how to register and update the Launch X431 CRP919X BT Diagnostic Tool . Follow the steps below to sign in and update: Tap Login on the upper right corner of the home screen, and the following login window will pop up. If you are a new user, follow A to proceed. If you have registered to be a member, go to B to log in to the system directly. In case you forgot your password, refer to C to reset a new password. A. If you are a new user, tap [New Registration] to enter the sign-up page. Fill in the information in each field (Items with * must be filled). After inputting, tap [Register], the following screen will appear: Input the 12-digit Product Serial Number and 8-digit Activation Code (which can be obtained from the password envelope), and then tap [Activate]. Tap [OK] to navigate to the update center to update all available software. After the registration is successfully complete, the wireless communication between the tablet and the VCI device is automaticall...
Read more

What is Launch X431 Key Programmer and how to use it?

Image
Launch x431 key programmer specializes in reading and writing key information, generating various key chips, etc. Currently, it can only be used with X431 IMMO Elite , X431 IMMO Plus , X431 PAD V (PAD 5), and X431 PAD VII (PAD 7) . How to use the x431 key programmer? 1. Use with Super Chips On the tablet (this item uses PAD V as an example), open the X431 PAD V APP, select "Other Modules" >> "Toolbox" >> "Key Programming" Enter the "Set Super Chip Type" menu to generate. Select the corresponding key chip type and insert the super chip into the anti-theft induction coil. Once successfully generated, it can be used. 2. Use with Super Remotes Take LS Nissan super remote as an example: The initial operation is the same as the super chip, enter the "Key Programming" menu and select "Vehicle Remote", then select the corresponding smart key model to generate. Place the electronic remote key in the key programmer to gener...
Read more

Launch X431 IMMO Plus Program Ford Engine Module Replacement

Image
This is a tutorial on how to use Launch X431 IMMO Plus to program Ford engine module replacement. Besides, the X431 IMMO Plus programming tool also supports anti-theft module replacement of BMW, Mercedes-Benz, VW/Audi, Honda, Nissan, Hyundai, etc. Read this article carefully to learn how to do it. Procedure Connect X431 IMMO Plus to car OBD. IMMO >> Ford >> Anti-theft system detection >> Automatically search Set the ignition switch to ON(Position II). Please confirm VIN and VIN code, and press "Yes". Immobilizer system function(expert edition) >> PATS(Passive Anti-Theft System) Functions Set the ignition switch to on. Module initialization >> PCM(powertrain control module) Set the ignition switch to OFF(Position 0). Operation in progress. Please wait until 100%... Set the ignition switch to ON. Retrieving data for coded access procedure... Please confirm VIN and VIN code, and press "Yes ". Set the ignition switch to OFF(Position 0). P...
Read more