Launch X431 ECU & TCU Programmer Clone Nissan ECU

Here's a demonstration of how to clone the 2014-2017 Nissan Leaf 23740 engine with Launch X431 ECU & TCU Programmer/ X-PROG3 PC Adapter + X431 GIII on bench. Both ECU tools are working the same way, you only need to have either one.


Procedure

Open X431 ECU & TCU Programmer/ X-PROG3 PC Adapter software.

Search: 23740

Select: Nissan, Leaf 2014-2017, EM61 EM61 109, 23740-3Nxxx-Genl_SH72531

Click "Direct connection of diagram".

Connect the original ECU according to the wiring diagram.

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-1

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-2

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-3

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-4

After a successful connection, click "Connect".

Read EEPROM data.

Save the EEPROM data file.

Read FLASH data.

Save the FLASH data file.

Click "Disconnect".

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-5

Re-connect to another ECU.

Backup EEPROM & FLASH data.

Write EEPROM data...

Data is successfully written.

Write FLASH data...

Data is successfully written.


A Nissan ECU clone has been done.

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-6

launch-x431-ecu-tcu-programmer-clone-nissan-ecu-7

www.obd2shop.co.uk

Comments

Post a Comment

Popular posts from this blog

Launch X431 CRP919X BT Register and Update

Image
This post will show you how to register and update the Launch X431 CRP919X BT Diagnostic Tool . Follow the steps below to sign in and update: Tap Login on the upper right corner of the home screen, and the following login window will pop up. If you are a new user, follow A to proceed. If you have registered to be a member, go to B to log in to the system directly. In case you forgot your password, refer to C to reset a new password. A. If you are a new user, tap [New Registration] to enter the sign-up page. Fill in the information in each field (Items with * must be filled). After inputting, tap [Register], the following screen will appear: Input the 12-digit Product Serial Number and 8-digit Activation Code (which can be obtained from the password envelope), and then tap [Activate]. Tap [OK] to navigate to the update center to update all available software. After the registration is successfully complete, the wireless communication between the tablet and the VCI device is automaticall...
Read more

What is Launch X431 Key Programmer and how to use it?

Image
Launch x431 key programmer specializes in reading and writing key information, generating various key chips, etc. Currently, it can only be used with X431 IMMO Elite , X431 IMMO Plus , X431 PAD V (PAD 5), and X431 PAD VII (PAD 7) . How to use the x431 key programmer? 1. Use with Super Chips On the tablet (this item uses PAD V as an example), open the X431 PAD V APP, select "Other Modules" >> "Toolbox" >> "Key Programming" Enter the "Set Super Chip Type" menu to generate. Select the corresponding key chip type and insert the super chip into the anti-theft induction coil. Once successfully generated, it can be used. 2. Use with Super Remotes Take LS Nissan super remote as an example: The initial operation is the same as the super chip, enter the "Key Programming" menu and select "Vehicle Remote", then select the corresponding smart key model to generate. Place the electronic remote key in the key programmer to gener...
Read more

Launch X431 IMMO Plus Program Ford Engine Module Replacement

Image
This is a tutorial on how to use Launch X431 IMMO Plus to program Ford engine module replacement. Besides, the X431 IMMO Plus programming tool also supports anti-theft module replacement of BMW, Mercedes-Benz, VW/Audi, Honda, Nissan, Hyundai, etc. Read this article carefully to learn how to do it. Procedure Connect X431 IMMO Plus to car OBD. IMMO >> Ford >> Anti-theft system detection >> Automatically search Set the ignition switch to ON(Position II). Please confirm VIN and VIN code, and press "Yes". Immobilizer system function(expert edition) >> PATS(Passive Anti-Theft System) Functions Set the ignition switch to on. Module initialization >> PCM(powertrain control module) Set the ignition switch to OFF(Position 0). Operation in progress. Please wait until 100%... Set the ignition switch to ON. Retrieving data for coded access procedure... Please confirm VIN and VIN code, and press "Yes ". Set the ignition switch to OFF(Position 0). P...
Read more